Experimental examination of the axial compression conduct of filament-wound cylindrical composite tubes at different wall thicknesses and orientation angles

Hayri Yıldırım

Article Details

Experimental examination of the axial compression conduct of filament-wound cylindrical composite tubes at different wall thicknesses and orientation angles

Authors:

Hayri Yıldırım

Publisher:

Dicle University

Main Topics:

Makine Mühendisliği (Diğer)

Journal:

Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi Vol.14 Issue 3, pp.455-460

Document Type:

Article

Publication Date:

9/2023

Document Language:

English

Document ID (Org No.):

2001299455

pISSN:

1309-8640

Keywords:

Abstract:

 This study presents the results of experimental research on the behavior and stretching of hollow cylindrical epoxy tubes made of glass, carbon, and kevlar fibers subjected to axial compression load. Hollow cylindrical tubes were fabricated by fiber winding method using glass, carbon, and kevlar fiber-reinforced composite materials. In this study, hollow cylindrical composite tubes with constant outer Ø17 millimeters, two different inner diameters Ø12 and Ø13 millimeters; 2 ve 2,5 millimeters wall thickness, and 80 millimeters in height. Experimental research was carried out for two dissimilar wall thicknesses and four fiber orientation angles. The compressive strengths of all samples were investigated experimentally by applying loads in the axial direction. Twenty-four configurations of composite specimens were fabricated three reinforcement materials, four winding angles, and two wall thicknesses to research the impact of axial compression stress. Experimental results revealed that polymer reinforcement material, fiber winding angle, and wall thickness have a significant impact on the compressive stress of cylindrical composite tubes as a result of applied load in the axial direction. The conclusions show that the compressive stress of all reinforcement rises as the orientation angle and wall thickness increase under an axial compression load, and the compressive stress reaches a maximum when the orientation angle is 90 under an axial compression load. It was observed that the axial compressive stress was highest in glassepoxy samples with 217 MPa, followed by carbonepoxy samples with 173 MPa and kevlarepoxy samples with 145 MPa, respectively. The axial compressive stress of all samples was highest at a 90 orientation angle and lowest at a 15 orientation angle. were found to have low values. It was observed that the axial compressive stress value increased in all reinforcement materials as the wall thickness increased. CRITICAL: Do Not Use Symbols, Special Characters, Footnotes, or Math in Paper Title or Abstract.

 This study presents the results of experimental research on the behavior and stretching of hollow cylindrical epoxy tubes made of glass, carbon, and kevlar fibers subjected to axial compression load. Hollow cylindrical tubes were fabricated by fiber winding method using glass, carbon, and kevlar fiber-reinforced composite materials. In this study, hollow cylindrical composite tubes with constant outer Ø17 millimeters, two different inner diameters Ø12 and Ø13 millimeters; 2 ve 2,5 millimeters wall thickness, and 80 millimeters in height. Experimental research was carried out for two dissimilar wall thicknesses and four fiber orientation angles. The compressive strengths of all samples were investigated experimentally by applying loads in the axial direction. Twenty-four configurations of composite specimens were fabricated three reinforcement materials, four winding angles, and two wall thicknesses to research the impact of axial compression stress. Experimental results revealed that polymer reinforcement material, fiber winding angle, and wall thickness have a significant impact on the compressive stress of cylindrical composite tubes as a result of applied load in the axial direction. The conclusions show that the compressive stress of all reinforcement rises as the orientation angle and wall thickness increase under an axial compression load, and the compressive stress reaches a maximum when the orientation angle is 90 under an axial compression load. It was observed that the axial compressive stress was highest in glassepoxy samples with 217 MPa, followed by carbonepoxy samples with 173 MPa and kevlarepoxy samples with 145 MPa, respectively. The axial compressive stress of all samples was highest at a 90 orientation angle and lowest at a 15 orientation angle. were found to have low values. It was observed that the axial compressive stress value increased in all reinforcement materials as the wall thickness increased. CRITICAL: Do Not Use Symbols, Special Characters, Footnotes, or Math in Paper Title or Abstract.

 This study presents the results of experimental research on the behavior and stretching of hollow cylindrical epoxy tubes made of glass, carbon, and kevlar fibers subjected to axial compression load. Hollow cylindrical tubes were fabricated by fiber winding method using glass, carbon, and kevlar fiber-reinforced composite materials. In this study, hollow cylindrical composite tubes with constant outer Ø17 millimeters, two different inner diameters Ø12 and Ø13 millimeters; 2 ve 2,5 millimeters wall thickness, and 80 millimeters in height. Experimental research was carried out for two dissimilar wall thicknesses and four fiber orientation angles. The compressive strengths of all samples were investigated experimentally by applying loads in the axial direction. Twenty-four configurations of composite specimens were fabricated three reinforcement materials, four winding angles, and two wall thicknesses to research the impact of axial compression stress. Experimental results revealed that polymer reinforcement material, fiber winding angle, and wall thickness have a significant impact on the compressive stress of cylindrical composite tubes as a result of applied load in the axial direction. The conclusions show that the compressive stress of all reinforcement rises as the orientation angle and wall thickness increase under an axial compression load, and the compressive stress reaches a maximum when the orientation angle is 90 under an axial compression load. It was observed that the axial compressive stress was highest in glassepoxy samples with 217 MPa, followed by carbonepoxy samples with 173 MPa and kevlarepoxy samples with 145 MPa, respectively. The axial compressive stress of all samples was highest at a 90 orientation angle and lowest at a 15 orientation angle. were found to have low values. It was observed that the axial compressive stress value increased in all reinforcement materials as the wall thickness increased. CRITICAL: Do Not Use Symbols, Special Characters, Footnotes, or Math in Paper Title or Abstract.

 This study presents the results of experimental research on the behavior and stretching of hollow cylindrical epoxy tubes made of glass, carbon and kevlar fibers subjected to axial compression load. Hollow cylindrical tubes were fabricated by fiber winding method using glass, carbon, and kevlar fiber-reinforced composite materials. In this study, hollow cylindrical composite tubes with constant outer Ø17 millimeters, two different inner diameters Ø12 and Ø13 millimeters; 2 ve 2,5 millimeters wall thickness, and 80 millimeters in height. Experimental research was carried out for two dissimilar wall thicknesses and four fiber orientation angles. The compressive strengths of all samples were investigated experimentally by applying loads in the axial direction. Twenty-four configurations of composite specimens were fabricated three reinforcement materials, four winding angles, and two wall thicknesses to research the impact of axial compression stress. Experimental results revealed that polymer reinforcement material, fiber winding angle, and wall thickness have a significant impact on the compressive stress of cylindrical composite tubes as a result of applied load in the axial direction. The conclusions show that the compressive stress of all reinforcement rises as the orientation angle and wall thickness increase under an axial compression load, and the compressive stress reaches a maximum when the orientation angle is 90 under an axial compression load.

Article Details

Experimental examination of the axial compression conduct of filament-wound cylindrical composite tubes at different wall thicknesses and orientation angles

Authors:

Hayri Yıldırım

Publisher:

Dicle University

Main Topics:

Makine Mühendisliği (Diğer)

Journal:

Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi Vol.14 Issue 3, pp.455-460

Document Type:

Article

Publication Date:

9/2023

Document Language:

English

Document ID (Org No.):

2001299455

pISSN:

1309-8640

thin-walled cylindrical tubes

filament winding process

mechanical analysis

failure behavior

polymer reinforcementsthin-walled cylindrical tubes

filament winding process

mechanical analysis

failure behavior

polymer reinforcements

Issues

Article Details

Authors: Hayri Yıldırım

Publisher: Dicle University

Main Topics: Makine Mühendisliği (Diğer)

Journal: Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi Vol.14 Issue 3, pp.455-460

Document Type: Article

Publication Date: 9/2023

Document Language: English

Document ID (Org No.): 2001299455

pISSN: 1309-8640

Issues

Authors:

Hayri Yıldırım

Publisher:

Dicle University

Main Topics:

Makine Mühendisliği (Diğer)

Journal:

Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi Vol.14 Issue 3, pp.455-460

Document Type:

Article

Publication Date:

9/2023

Document Language:

English

Document ID (Org No.):

2001299455

pISSN:

1309-8640